Today we start offering the square Micro 64 probes that you have been looking for!

These probes are available in a pack of 3 Male and 3 Female probes.

 

Typical Applications:

·         Automotive and commercial vehicles

·          Engine management systems

·          Powertrain control systems

·          ABS braking systems

·          Airbag systems

These are Tyco terminal part numbers 963716-1 (male) and 963715-1 (female). The Male pin measures .644mm. These probes fit terminals found in the following vehicles:

2010 - 2013 Buick LaCrosse

2011 - 2013 Buick Regal

2012 - 2013 Buick Verano

2007 - 2013 Cadillac Escalade Models

2006 - 2013 Cadillac CTS

2006 - 2011 Cadillac DTS

2004 - 2013 Cadillac SRX

2005 - 2011 Cadillac STS

2007 - 2013 Chevrolet Avalanche, Suburban, Silverado, Tahoe

2004 - 2011 Chevrolet Aveo

2005 - 2010 Chevrolet Cobalt All Models

2011 - 2013 Chevrolet Cruze

2010 - 2013 Chevrolet Equinox

2006 - 2011 Chevrolet HHR

2005 - 2013 Chevrolet Malibu

2006 - 2013 Chevrolet Impala

2012 - 2013 Chevrolet Sonic

2011 - 2013 Chevrolet Volt

2007 - 2013 GMC Sierra, Yukon And Denali Models

2010 - 2013 GMC Terrain

2007 - 2010 Pontiac G3

2007 - 2010 Pontiac G5

2005 - 2010 Pontiac G6

2008 - 2009 Pontiac G8

2005 - 2006 Pontiac  Pursuit (Canada Only)

2006 - 2010 Pontiac Solstice

2005 - 2010 Pontiac Wave (Canada Only)

2010 - 2013 Buick LaCrosse
2011 - 2013 Buick Regal
2012 - 2013 Buick Verano
2007 - 2013 Cadillac Escalade Models
2006 - 2013 Cadillac CTSThese are Tyco terminal part numbers 963716-1 (male) and 963715-1 (female). The male probe measures .64 mm.
These probes fit terminals found in the following vehicles:These are Tyco terminal part numbers 963716-1 (male) and 963715-1 (female). The male probe measures .64 mm.
These probes fit terminals found in the following vehicles:

Company Information

Jumperkits, LLC

10043 Hackensack St

Port Charlotte, FL 33981

Contact – Mike Balog

Cell – 231-645-2748

Web site – www.Jumperkits.com

Drag Test – Another use for Jumperkits

Intermittent operation of electrical components can often be caused by poor electrical connections. Poor connections can be caused by;

·         Corroded connector terminals

·         Pins or sockets  that are pushed back into the connector body

·         Poorly mated connector terminals

·         Loose pins

·         Worn out pins or sockets

Corroded terminals can be easily identified by disconnecting the connector bodies and carefully examining the pins and sockets for any corrosion. Any terminals that show signs of  corrosion should be replaced.

Pushed back pins or sockets can also be found through visual inspection and also require replacement. Sometimes the cause of the loose terminal may be a worn out body, rather than the terminal itself. If this is the case, replace the connector body and any required terminals.

If nothing is visibly wrong, poorly mated, loose, or worn out terminals can be discovered by performing a “drag test” using the correct wire from our Jumperkits.

Select the correct mating terminal from the Jumperkit and manually insert it into the terminal in the connector. As you slide the terminal in and out, it should fit securely and you should feel a significant amount of “drag”. If not, the terminal should be replaced.

Test Probes for Square Micro 64 Termnals

When we added the Round Micro 64 test probes to our Jumperkits, many of our customers expressed an interest in probes for the newer square Micro 64 terminals.

It took some time, but we finally have located the correct terminal numbers for both the male and female terminals! We found a supplier for them, and expect to have them in stock in 4 to 5 weeks.

We will be adding 3 of each gender to the 18001.10-KIT and offering an separate update kit for those customers who already own the 18001.10-KIT and just want to add the Square Micro 64 probes.

New products on our web site!

New Complementary Products are in!

4 new products to complement your Jumperkits!

We are now offering 4 products that we think are valuable additions to your Jumperkit probe sets.

·         Fused Automotive DMM test leads from ESI – great added protection for that expensive automotive meter you own! Uses a standard automotive fuse in-line instead of blowing the internal fuse in you meter. Much easier to replace! (Manufacturers # ESI134)

·         Alligator Clips for your meters pointed probes from UEI – handy to have accessory when you have a bare wire that you just need to clip a meter's test lead onto. (Manufacturers # UEIAAC)

·         A terminal release tool from Lisle – remove wires from terminal blocks without damage! Once you've found a bad terminal, this handy tool is a must have to release the terminal from the terminal block so you can replace it. (Manufacturers # LIS56500)

·         A terminal release tool from OTC – Works on most import and domestic vehicles! (Manufacturers #